Delafield Nova Equipment Flash content requires javascript to be enabled in your web browser.
  • Hydraulic Power Units (HPU)
  • Service Loops: Electrical
  • Service Loops: Hydraulic

Hydraulic Power Units (HPU)

Delafield has the capabilities to design and manufacture Hydraulic Power Units to meet the exacting requirements of most industries. The Delafield team will work with your technical staff to deliver a product that exceeds your expectations for quality and cost efficiency. Delafield has manufactured HPU’S with oil capacities of 50 to 700 gallons, 50 and 60 Hz motors, flow rates of 15 to 200 gpm, and pressure to 5000 psi. All HPU’s can be supplied with UL listed CSA listed or ATEX certified components, and fully wired and tested.


You can select from one of Delafield’s standard Hydraulic Power Units or we can design a custom unit with the following features:

  • 25 hp (19 kW) to 400 hp (300 kW)
  • Single or Multiple Pump Configurations
  • Flows from 15 gpm (57 lpm) to 300 gpm (1135 lpm)
  • Pressures up 5000 psi ( 345 bar)
  • 50 or 60 Hz, 380 through 690 VAC
  • Stainless Steel tanks and corrosion resistant frames
  • With or without Starters and control Circuits
  • UL or ATEX components for hazardous areas
  • Immersion heaters
  • Duplex filtration, and ease of maintenance designs
  • Reduced noise levels
  • Full factory functional testing

Hydraulic Power Unit Photo Galleries
Delafield Corporation

Hydraulic Power Units (HPU)

Delafield has the capabilities to design and manufacture Hydraulic Power Units to meet the exacting requirements of most industries. The Delafield team will work with your technical staff to deliver a product that exceeds your expectations for quality and cost efficiency. Delafield has manufactured HPU’S with oil capacities of 50 to 700 gallons, 50 and 60 Hz motors, flow rates of 15 to 200 gpm, and pressure to 5000 psi. All HPU’s can be supplied with UL listed CSA listed or ATEX certified components, and fully wired and tested.


You can select from one of Delafield’s standard Hydraulic Power Units or we can design a custom unit with the following features:

  • 25 hp (19 kW) to 400 hp (300 kW)
  • Single or Multiple Pump Configurations
  • Flows from 15 gpm (57 lpm) to 300 gpm (1135 lpm)
  • Pressures up 5000 psi ( 345 bar)
  • 50 or 60 Hz, 380 through 690 VAC
  • Stainless Steel tanks and corrosion resistant frames
  • With or without Starters and control Circuits
  • UL or ATEX components for hazardous areas
  • Immersion heaters
  • Duplex filtration, and ease of maintenance designs
  • Reduced noise levels
  • Full factory functional testing

Hydraulic Power Unit Photo Galleries
Delafield Corporation

Service Loops: Electrical

Delafield Corporation has been manufacturing Service Loops for various Top Drive manufacturers for over 15 years. With the knowledge that we have acquired from these years we have developed and patented (US and foreign patents pending) an improved service loop design. This patented design is the only major improvement in service loop technology since the fist loops were built in 1982. Our new loop design allows for the securing of each loop to prevent excessive movement and damage due to wind and motion; increasing the life of the loops.


This restraint system combined with full length urethane potting and twisted cables (rope lay) results in Loops with higher densities and reduced lateral motion. Less unnecessary motion means loops last longer and can be installed in more demanding conditions.


Delafield can manufacture Electrical loops with all sizes of power conductors from 444 to 1111 MCM. Lengths from 50 foot to 200 foot, and diameters from 2 inch to 6 inch ID can be manufactured.


We currently manufacture Electrical Service Loops for several manufacturers and drilling contractors.


Please consult our engineering department for the Electrical Service Loop that meets your application.


Service Loop Photo Galleries
Delafield Corporation

Service Loops: Hydraulic

Delafield Corporation has been manufacturing Service Loops for various Top Drive manufacturers for over 15 years. With the knowledge that we have acquired from these years we have developed and patented (US and foreign patents pending) an improved service loop design. This patented design is the only major improvement in service loop technology since the fist loops were built in 1982. Our new loop design allows for the securing of each loop to prevent excessive movement and damage due to wind and motion; increasing the life of the loops.


This restrain system combined with full length urethane potting and high quality hydraulic and pneumatic hoses results in Hydraulic Service Loops with long life and exceptional performance. As with the Electrical Loops, less unnecessary motion means these loops last longer and can be installed in places where lighter, flimsier loops will not survive.


Delafield can manufacture Hydraulic Loops with hose sizes from 1/2 to 1 inch ID (up to 200 foot) and from 1-1/4 to 2 inch ID (up to 100 foot). Diameters from 2 inch to 6 inch ID can be manufactured.


We currently manufacture Electrical Service Loops for several manufacturers and drilling contractors.


Please consult our engineering department for the Electrical Service Loop that meets your application.


Service Loop Photo Galleries
Delafield Corporation
 
1 2 3

Nova Equipment